Brevis...
Price: Estimated $3,000+
Likes: digital-like specs from analog amp
Dislikes: not in production yet
More info: Benchmark AHB2
by John Gatski
Benchmark Media has been in the audio game for more than 25 years. And although they are best known for their DACs and ADCs, they have never been afraid to delve into new areas of product development. So the recent introduction of the new audiophile stereo amplifier, the AHB2 was a nice surprise but not totally out of left field. In fact, the company’s founder, the late Allen Burdick created a high-quality amplifier back in the 1980s, the DA101 distribution amp that was highly regarded for many years.
The new compact AHB2 however, is a new design that takes amplification to another level in terms of measured specifications. In fact, the performance of this new analog amp rivals the measured performance of its world class DACs. The amp is slated for dealers in early January 2014.
The AHB2 design
According to John Siau, Benchmark’s chief designer and VP, the Benchmark AHB2 is a unique amplifier that was designed in conjunction with THX. The bipolar-output, 100 WPC RMS analog stereo amp (350W bridged mono) is housed in a compact enclosure that measures two times a DAC2 (11" W x 9"D to back of connector x 3 7/8"H). Despite its modest proportions, the AHB2 boasts numerous design highlights that enable it to deliver measured specifications as good as its digital converters, especially its noise and dynamic range performance.
“It was my goal to create a power amplifier that matched the performance of the DAC2 D/A converter,” Siau explained. “After all, the performance of the D/A converter is only useful — if it can be delivered by the downstream power amplifier.”
I applaud Benchmark’s efforts to clean up analog amplifier noise. That low-level idle hiss that I hear from numerous vintage and modern amplifiers is, at the very least, annoying, and, at its maximum, detrimental to ultimate resolution.
Siau said that the amp has exceeded his expectations in terms of measured performance. The SNR of the AHB2 was spec'd at 126 dB (A-weighted) and THD is -115 dB, just about as good as the DAC2’s measurements. “The AHB2 power amplifier was designed from the ground up to deliver the full performance of the DAC2 HGC," he emphasized.
Siau furnished me with an Audio Precision System 2 measurement of the prototype AHB2 that I spent a few days with recently. The dynamic range was -130 dB, A-weighted! I don’t think I have ever seen (or heard) a hi-fi amp with such specs. Back in the 1980s, I remember sold state amps with a typical -85 dB dynamic range/noise spec.
In order to achieve the new spec, Siau utilized THX amplifier design concepts, as well as applying some of his engineering prowess in order to get these impressive numbers, and as I found out in my brief listening sessions, impressive listening results.
Digital specs, analog amp
Siau said the following design highlights enabled Benchmark to create the AHB2’s “fantastic” performance signature.
•Low gain (9 dB). This allows +22 dBu input at amplifier clip, which is essential for low noise;
•Patented feed-forward error correction, which virtually eliminates crossover distortion, a problem Siau says is still common among typical amplifier designs;
•The feed-forward design also makes bias currents unnecessary, and non-critical. Thus, Class B operation is possible with very low distortion;
•The multiple bipolar output stages are run in parallel to eliminate crossover distortion; one output stage is active, while another is in the crossover region;
•The Class AB output stage uses very low bias current. (Due to low bias currents, idle power consumption is only 20 watts.);
•The feed-forward design even makes the more efficient Class H or G operation possible — with no rise in distortion at class H or G switch point (Class H , or G, rail switching at a 1/3 power threshold);
•A tightly regulated power supply — with high-bandwidth control loop on the switch-mode power supply — responds to amplifier loading over the entire audio band, and at ultrasonic frequencies;
•The amplifier does not rely on capacitive energy storage, and the switch-mode power supply eliminates AC line magnetic interference to levels not possible with a linear power supply
•The AHB2’s greater than 200 kHz bandwidth allows it to achieve excellent inter-channel phase at 20 kHz and greater than 0.1 Hz low-frequency cutoff is said to minimize low-frequency phase shift;
•The feed-forward design also improves damping factor for improved bass response, and the PCB uses balanced star-quad signal and power supply distribution to minimize magnetic interference.
**Siau said that certain THX design elements allow him to make the amp as efficient as possible, but the AHB2 design was optimized for low distortion and low noise.
As I got into serious listening of recordings, I was impressed by the AHB2’s "smooth factor. Although it uses bipolar output devices, its tonal delivery ease reminds more of MOSFET designs. Drum cymbals and the upper register of the Bernhard album’s piano sounded fantastic without any edge, grit or harshness.
“It was not optimized for the highest possible efficiency that could be achieved with the new THX topology”, Siau explained. “Nevertheless the AHB2 is much more efficient than a conventional Class AB design. Peak power does not vary with AC line voltage (due to the regulated supply). Likewise, power drawn on one channel does not influence the power available from the other channel.”
**Though the ABH2 utilizes a switching power supply, Siau emphasized that the overall amp design is not a switcher. “The AHB2 is a linear amplifier, it is not a switcher,” he noted. “For this reason, it produces very little out-of-band noise. The A-weighted noise is only 2 dB less than noise measured over an 80 kHz bandwidth. This was an important design goal because ultrasonic noise can be folded into the audio band by the non-linearities in speaker transducers.”
The ins and outs
Siau sent me one of two ABH2 prototypes to conduct a few days of subjective listening in late October. He said that there would likely be a few more tweaks in the final version, but the prototypes represented the essential sonic signature of the design.
The ABH2 is a simple amp to operate. It includes a front power on/off switch, binding posts (final version will have binding posts with easier access than the prototype’s horizontal-aligned speaker inputs), balanced analog inputs and a 12V trigger input.
You can also bridge the amp to mono, via a rear toggle panel switch, to get 350 watts (8 ohms). Thus, buying two stereo amps and bridging mono for each one would be the chosen path for powering the less efficient speakers, or filling big rooms.
You can also bridge the amp to mono, via a rear toggle panel switch, to get 350 watts (8 ohms). Thus, buying two stereo amps and bridging mono for each one would be the chosen path for powering the less efficient speakers, or filling big rooms.
 |
| Production AHB2 will get optimized conection access |
Since the amp is not a high-gain amp, ensuring gain match with your source preamp is a consideration. The Benchmark DAC2 HGC and DAC2 D have enough gain in the stock setting on various audiophile recordings. However, if you move a jumper inside the DAC you can get 10 dB more gain to give extra headroom.
I played around with various gain components during my time with the AHB2, including the Coda preamp, Oppo BDP-105 variable balanced output, and the DAC2 D's variable output.
The Oppo BDP-105’s variable or fixed output, even at full blast, was just enough gain, but not ideal Benchmark’s Siau said that the production AHB2 will have three gain settings (with virtually the same noise spec), and offers more flexibility for preamp choices than the single (low-gain) setting that was active on the prototype. “This (three-position gain level switch) makes the AHB2 compatible with all preamplifiers, but preamps that do not have high output usually have a poor signal-to-noise ratio, and will, therefore limit the system performance.”
The Oppo BDP-105’s variable or fixed output, even at full blast, was just enough gain, but not ideal Benchmark’s Siau said that the production AHB2 will have three gain settings (with virtually the same noise spec), and offers more flexibility for preamp choices than the single (low-gain) setting that was active on the prototype. “This (three-position gain level switch) makes the AHB2 compatible with all preamplifiers, but preamps that do not have high output usually have a poor signal-to-noise ratio, and will, therefore limit the system performance.”
Like the Benchmark DAC2 D, the Coda preamp was a better fit than the Oppo’s variable output. It had to be cranked a few more clicks on the volume control to get to the level of my normal amps, but they were still able to drive the Benchmark to plenty loud levels without noise.
For those who listen with very accurate, discerning speakers, an extra 20 dB of lower noise could be heard — in terms of ultra detail that may be hiding in the noise of an average audiophile amp.
Sources for the AHB2 listening sessions included the Oppo BDP-105, Benchmark DAC2 D, TASCAM DVRA1000 HD master recorder/player, and Apple Macbook Pro feeding a Mytek Stereo192-DSD DAC. Preamps included a Coda, a Pass Labs XP-10 passive preamp, Rogue Audio Model 99 tube preamp, and the line output of the Bryston BHA-1 headphone amplifier.
Speakers included the Pass Labs SR1 three-way towers, MartinLogan Montis electrostatics (though the bass is handled in the speaker via a sealed powered subwoofer), Westlake Audio Tower 6, the best sounding Westlake hi-fi speaker and a pair of Westlake LC 8.1's and the ever-popular Legacy Studio stand-based small speakers.
All interconnects were furnished by WireWorld. Speaker cables were courtesy of Alpha Core; Essential Sound Products provided the AC distribution gear including the Essence II passive power strip and several Essence II power cords that give clamp like connection to the wall and low-noise shielding.
A brief audition
The AHB2 was first mated to the Pass SR1 tower speakers, the company’s entry -evel tower, which is an excellent three-way (review in just a few weeks) with quick, deep bass and silky top end.
First up was the Warren Bernhardt — So Real SACD, a recording that has a full dynamic range and spacious soundstage with piano, drums and bass. I connected the Oppo BDP-105 XLR balanced output to my CODA preamp. Because of the prototype amp’s low-gain only setting and a Benchmark caution that preamps need to have abundant gain to drive the amp, I was curious as to how the various preamps would fare.
Because the Bernhardt recording was recorded live-to-two tracks, its vast dynamic range is quite apparent, which means the quiet parts are quiet, and the louder parts are, well loud; thus, if you want to hear it loud, especially the softer parts, you got to crank it up a bit with this amp.
I am happy to report that the Coda’s gain structure matched up well with the AHB2. I had to turn it up a few more clicks on the volume control, but there was plenty of level without noise.
The first thing I noticed with the AHB2 is the lack of idle noise. Put your ears to the tweeter and none of the low level hiss you hear with conventional, high-gain amps can be heard. With no signal, nary a whisper from the Benchmark even when cranking up the CODA (or other preamps as I later discovered).
 |
| Pre-brochure AHB2 Specs |
As I got into serious listening of recordings, I was impressed by the AHB2’s "smooth factor. Although it uses bipolar output devices, its tonal delivery ease reminds more of MOSFET designs. Drum cymbals and the upper register of the Bernhard album’s piano sounded fantastic without any edge, grit or harshness. The dynamics of the So Real recording jumped out at me when listening to the AHB2 — with a deep, wide stereo image and an encompassing presentation of the subtle layers of each instrument and their ultimate interaction with each other. This quality was repeated through numerous other recordings as well.
On the Gene Bertoncini — Body and Soul SACD, the warm, percussive guitar tones shone with this amp producing a wide spread of plucked notes. The low noise floor of the AHB2 however, was swallowed up by the recording's tube mic noise, but still the expansive stereo image and nylon string guitar’s dynamics were up there with the best amps I have auditioned.
Switching to the MartinLogans and using the Benchmark DAC2 D D/A as a preamp with high-res PCM digital sources, the AHB2 again revealed its dynamic, clean, quiet character. The exquisite layers produced via the MLs were even more in evidence with the AHB2. The Tuck and Patti — With Love CD has a unique blend of vocal and guitar interplay that is mixed in a focused, yet open character. The Benchmark brings out the quick, percussive guitar attack with amazing clarity, but no over-the-top edginess that lesser bi-polar (and even some MOSFET amps).
 |
| The DAC2 and AHB2 make a dandy pair |
Being that it is the first complete prototype of the Benchmark AHB2, I am not worried about the midbass prominence I heard in the brief audition. I am sure Mr. Siau will have this amp in fine form when the production units hit the dealers in a couple of months. In addressing my notes regarding the bass performance, Siau said “there are, in-fact, numerous improvements coming in the next revision. We have revised the Zobel network, over-current protection, power supply, and input sections, just to name a few of the changes.”
Is noise a noise, if you can’t hear it?
In discussing Benchmark’s impressive amp specs with several audio industry insiders, several of them questioned the necessity of an ultra low-noise floor/ultra dynamic range in the amplifier chain. Does it matter if there is some idle hiss after the music starts to play? And can one hear the enhanced quietness versus an amp that measures, say -100 dB?
I look at it this way: line sources, DACs, players, etc. have exhibited generational improvements in measured performance, and I believe these improvements have brought progressive audible, if subtle, improvements as well. For those who listen with very accurate, discerning speakers, an extra 20 dB of lower noise could be heard — in terms of ultra detail that may be hiding in the noise of an average audiophile amp.The -130 dB noise/dynamic range just gets us that much closer to the live music signature that we yearn to hear from our beloved electronics.
So, at the end of the day, I applaud Benchmark’s efforts to clean up analog amplifier noise. That low-level idle hiss that I hear from numerous vintage and modern amplifiers is, at the very least, annoying, and, at its maximum, detrimental to ultimate resolution. I can’t wait to hear the final version of the AHB2.
John Gatski is publisher/owner of the Everything Audio Network. ©Articles on this site are the copyright of the Everything Audio Network. Any unauthorized use, via print or Internet, without written permission is prohibited.
Are you getting the final version in demo? I'am considering this amp to drive my Martin Logan Summit X's, at least test drive is coming.
ReplyDelete